Area, built from slices
The definite integral adds up thin slices. First under one curve, then between two.
1. Area under a curve
Cut the interval [a, b] into n strips of width Δx = (b − a)/n. Each strip gets a height from f, and the total area of the strips approximates ∫ab f(x) dx. As n → ∞, the sum becomes the integral exactly.
BC habit: on an increasing function, left sums underestimate and right sums overestimate. On a decreasing function it flips. Midpoint and trapezoid sums depend on concavity: trapezoids overestimate when f is concave up, midpoints underestimate.
2. Area between curves
Slice vertically. Each slice has width dx and height (top − bottom), so
Area = ∫ab [ f(x) − g(x) ] dx, where f ≥ g on [a, b].
Drag the slice below to watch the height change. If the curves cross, the top and bottom swap, so split at each crossing or integrate |f − g|.
Also on the exam: if the region is easier to describe with horizontal slices, integrate (right − left) dy instead. The idea is the same: far side minus near side.
3. Slicing horizontally (dy)
Some regions are easier with horizontal slices. Each slice has height dy and length (right − left), so Area = ∫ [xright(y) − xleft(y)] dy. Here the region sits between x = y² and x = 2 − y.
Limits: y² = 2 − y gives y = −2 and y = 1.
Area = ∫−21 [(2 − y) − y²] dy = [ 2y − y²/2 − y³/3 ] from −2 to 1 = 9/2
Vertical slices would need two integrals here, because the lower boundary changes at x = 1. Horizontal slices need one.
4. Improper integrals
When an interval is infinite, define ∫1∞ f(x) dx = limt→∞ ∫1t f(x) dx. If that limit is a finite number the integral converges. Otherwise it diverges. Drag t, then read the table for larger t.
p-test: ∫1∞ 1/xp dx converges exactly when p > 1. That is why 1/x² converges while 1/x and 1/√x do not.
5. Volume by disks and washers
Revolve a region about the x-axis. A slice at x becomes a washer with outer radius R(x) and inner radius r(x), so its area is π(R² − r²). Then V = π ∫ab [R(x)² − r(x)²] dx. For a solid disk, r = 0.
Left: the region and its reflection across the x-axis. Right: the face of the slice, a ring between r and R. Revolving about a horizontal line y = k just shifts the radii to R − k and r − k.
6. Improper integrals at a discontinuity
If f blows up at an endpoint, replace that endpoint with t and take a limit: ∫01 f dx = limt→0⁺ ∫t1 f dx. Here the p-test flips: ∫01 1/xp dx converges exactly when p < 1.
Slide t toward 0 and watch the curve climb. The slider runs from t = 1 down to t = 0.01, and the table pushes t much closer to 0.
7. Known cross-sections
Take a base region in the xy-plane and stand a shape on each vertical slice, perpendicular to the x-axis. If the shape has area A(x), the volume is V = ∫ab A(x) dx. The width w(x) of the base at x is the side or diameter of the shape. Here the base lies between y = x² and y = x, so w(x) = x − x².
Area formulas to know: square with side w: w². Semicircle with diameter w: πw²/8. Equilateral triangle with side w: (√3/4)w². Rectangle with base w and height h(x): w·h.
Check yourself
Thirty-five multiple-choice questions and three free-response problems, each tagged Easy, Medium, or Hard. Filter by level here, and add a user at the bottom of the page to save progress in this browser.
Free response
Work each part on paper first. Enter a decimal, a fraction like 4/3, or a multiple of π like 8π/3. Answers within 0.01 are accepted. Open the solution when you are ready to compare.
Users
Progress is saved per user, in this browser only.